NEED HELP (PRUSA I3 MK3S+) FILAMENT STUCK (CANT PULL NOR PUSH
I had the same problem about a month ago, but it was caused from my filament spool ending so I didn't have any blobs. I just persevered with heating in high degrees (it was PETG, so I went … From reddit.com
FILAMENT STUCK – ASSEMBLY AND FIRST PRINTS ... - PRUSA3D FORUM
Jun 7, 2024 You can try shoving the filament down from the top, or grabbing it with needle nose plyers, but most of time you have to do a partial disassembly to clear to remove it. I've had this … From forum.prusa3d.com
STUCK FILAMENT DETECTION CAUSING FILAMENT TO GET STUCK?
May 27, 2024 I tried the new stuck filament detection (with the load cell) in 6.0.0 firmware. When it's on I get a stuck filament warning on almost every print, and it turns out the filament is … From forum.prusa3d.com
FILAMENT GETS STUCK DURING UNLOADING #1095 - GITHUB
Aug 30, 2018 Hello, I have found that filament can easily get stuck in the hot end PTFE tubing during the unload process. Occasionally a small blob breaks off in the hot end PTFE tubing … From github.com
PLEASE HELP ME RESOLVE THE CONSTANT "FILAMENT STUCK" ERRORS
Sep 20, 2024 The "filament stuck" problem started showing up after about a week. I'm only printing PLA so far, so I suspected the filament softening in the feeder due to the higher … From forum.prusa3d.com
[BUG] STUCK FILAMENT DETECTED WITH MMU3 #4110 - GITHUB
Jul 30, 2024 Start print and after few or couple minutes stops print becuase of Stuck Filament Detection. The issue started to happen after update from 6.0.2 firmware. The Issue is … From github.com
REMOVING FILAMENT FROM EXTRUDER MANUALLY | PRUSA …
Feed in from the top of the extruder your tool of choice, down past the Bondtech-gear, and on top of the stuck filament. If you are able to push the stuck filament down the PTFE-tube with an Allen-wrench, switch to using filament after about … From help.prusa3d.com
PLEASE HELP. FILAMENT STUCK IN NEW MINI : R/PRUSA3D - REDDIT
Please help. Filament is stuck and unloading doesn’t work. It is physically stuck. What can I do? As per instructions I have set hotend temp to 260c to cause excess filament to melt out. … From reddit.com
From what I've seen, people have tried, but all have failed to get stuck filament out once it is stuck. The correct PTFE tube depends on your exact model, e.g. https://www.prusa3d.com/product/hotend-ptfe-tube-mk3s-mmu2s/ From reddit.com
Sep 14, 2024 I was able to save the print by using the tuning settings to force a filament change (simply re-inserting the same filament) and re-enabled the stuck filament sensor. It was able to finish out the print afterwards. From forum.prusa3d.com
HOW DO YOU PREVENT FILAMENT GETTING STUCK? : R/PRUSA3D - REDDIT
Heat it up to unload. It beeps at you. You grab the filament where it's loaded press the button. You immediately trim the end of the filament at an angle for reloading, then clip it to the side of your … From reddit.com
The attached photos show the stuck filament piece in the feeder and confirm that there is no filament residue on the gears themselves: The extruder mechanism where a piece of filament has become stuck within the feeder. From reddit.com
FILAMENT GETS STUCK REPEATEDLY DURING PRINTING - PRUSA3D FORUM
Oct 23, 2024 I am also experiencing the same problem, a "Stuck filament error", which is not solved when unloading and reloading the filament. Initially I thought it was due to me using a … From forum.prusa3d.com
Oct 22, 2021 If your extruder is still jammed, you likely have filament stuck inside the actual extruder. Closely examine the PTFE tubing sticking up below the gears. The PTFE tubing itself … From muppetlabs.co
STUCK FILAMENT DETECTION NOT WORKING #4086 - GITHUB
The stuck filament would be detected using the load cell sensor. If stuck filament occurs, the print should immediately stop, and: Maintain the bed temperature; alert the user the fault has … From github.com
FILAMENT STUCK IN EXTRUDER SOMEWHERE - PRUSA3D FORUM
Aug 21, 2023 I got halfway through a 8hr print when filament just stopped coming out. I tried to purge but the gears just kept slipping along the filament and did the same thing when trying to … From forum.prusa3d.com
Heat up the hot end to PETG levels, and push new filament behind it until the color changes. Then stop power down, close up that filament feed mechanism to reengage and have the printer do its unload step on the new filament. From reddit.com
PRUSA XL "CLOGGED", WON'T FEED MATERIAL TO EXTRUDER : R/3DPRINTING
These tell how to fix the unclog the hot end or set tension screws. My issue is there's a piece of filament stuck in that middle piece of plastic, that looks like a horizontal tube. There's a hole in … From reddit.com
The Original Prusa MK4/S, MK3.9, and XL are equipped with a loadcell. Thanks to this component, starting from firmware 6.0.0, the printer is able to detect whether the filament is stuck and not moving, for example when the nozzle is … From help.prusa3d.com
Are you curently on diet or you just want to control your food's nutritions, ingredients? We will help you find recipes by cooking method, nutrition, ingredients...