Texas Style Beef Ribs Food

AUTHENTIC TEXAS-STYLE SMOKED BEEF RIBS RECIPE

Steps:

• Prep. Begin by removing the fat and the very tough silverskin from the top of the meat. All of it. It will not melt and penetrate. No need to remove the membrane from the exposed side of the bones as you do with pork ribs. If you do the meat can fall off. Then cut slabs into individual bones or double bones if they did not come cut up. You can cook them in a slab, but they take a lot longer, and for Texas style, I like to expose more surface to heat to tenderize and develop brown Maillard reaction flavors. I prefer to cut them into two bone sections. Inevitably some bones in a package have little meat and lotta fat. Trim them anyhow and cook them.
• Salt the meat in advance, up to 24 hours. This is called dry brining and it is important for water retention (juiciness) and flavor enhancement. Just before cooking, wet the surface of the meat lightly with water and flavor the meat with my Big Bad Beef Rub. Most commercial rubs are primarily salt: avoid them. While you may be tempted to use my recipe for Meathead's Memphis Dust, don't: it's perfect for pork, but too sweet for beef. Sprinkle the beef rub on the tops and sides, and coat the meat generously.
• If you wish, you can tenderize the meat with a meat tenderizer such as Jaccard. The narrow blades sever long tough strands and do a pretty good job. I normally do not recommend this tool because, if there is contamination on the surface of the meat, the blades can drive the bugs into the center and they will not be killed at 130°F (54.4°C), medium rare. But at 165°F (73.9°C) the meat is pasteurized through and through and you will be cooking this cut to more than 200°F (93.3°C).
• Fire up. Setup your cooker for indirect cooking and preheat to 225°F (107.2°C), hot enough to kill bacteria but not too high to evaporate all the moisture.
• Put the meat on the indirect heat side of the grill, bone side down, and add the wood. Oak is traditional in Texas and it makes sense because it is mild, but other woods work fine. I like cherry. As always, go easy on the wood. Too much smoke will ruin the meal. Add no more than 2 to 4 ounces (56.7 to 113.4 g) on a tight cooker, double that if it leaks a lot. Put the lid on. You will not need to add more wood and you will not need to turn the meat over.
• The exact length of the cook depends on variables such as the composition of the meat (each steer is different). As an estimate, 1"- (2.5 cm-) thick meat should hit 203°F (95°C) in about 5 hours; 1.5-inch (3.8-cm) thick meat should hit 203°F (95°C) in about 7 hours; and 2-inch (5.1-cm) thick meat should hit 203°F (95°C) in about 10 hours.
• Despite what you may read elsewhere, skip the Texas crutch. Wrapping it in foil or butcher paper can turn it to pot roast.
• Once fully cooked, skip the BBQ sauce if you're going for authentic Texas smoked beef ribs. If you must use a sauce, try what they use in Texas, a thin beef stock based sauce, like my Texas Barbecue Mop Sauce.

TEXAS BBQ BEEF RIBS

Steps:

• Pour wood chips into the hopper of a pellet grill according to manufacturer's instructions. Set temperature to 275 degrees F (135 degrees C).
• Trim ribs with a sharp knife to remove as much fat and silver skin from the top of the ribs as possible. Leave the membrane on the bottom of each rack as this will help hold them together as they cook.
• Place steak seasoning in a coffee grinder or food chopper. Grind to a medium coarseness to reduce the size of the salt crystals. Transfer to a shaker bottle. Add chili powder and garlic powder and shake until evenly combined.
• Rub 1/2 of the Worcestershire sauce on the bottom of the ribs as a binder, then sprinkle on a medium to heavy coat of the rub mixture. Flip ribs and repeat on the meaty side. Spritz a light coat of apple juice over top to help it "sweat."
• Immediately place ribs on the preheated pellet grill with the thicker side of the ribs towards the main heat source (toward the back, opposite the lid).
• Smoke ribs, spritzing them with a light coat of apple juice every 30 minutes to keep moist, until the internal meat temperature reaches 198 to 203 degrees F (92 to 95 degrees C), 4 to 6 hours. If it is taking longer don't be afraid to raise the heat to 325 degrees F (165 degrees C) but just watch the internal temperature a little closer, as the window of being done is smaller due to the higher cooking temperature. The temperature probe should slide into the meat like a brisket or like butter when they are ready.
• Remove ribs from the grill and place on a large cutting board. Slice into individual ribs to serve, or remove the meat and place on a tray to serve.